Nowadays, electrical accidents to the line man are increasing, while repairing the electrical lines due to the lack of communication between the electrical substation and maintenance staff. This project gives a solution to this problem to ensure line man safety. In this proposed system, the control (ON/OFF) of the electrical lines lies with line man. This project is arranged in such a way that maintenance staff or line man has to enter the password to ON/OFF the electrical line. Now, if there is any fault in electrical line, then the line man will switch off the power supply to the line by entering password and comfortably repair the electrical line, and after coming to the substation line man switch on the supply to the particular line by entering the password. Separate passwords are assigned for each electrical lines. Before going to know about this circuit, also read the interesting post: Password based door locking system.
Construction and Output Video
Block Diagram
Principle of Operation
The main component in the circuit is 8051 microcontroller. In this project 4×4 keypad is used to enter the password. The password which is entered is compared with the predefined password. If entered password is correct, then the corresponding electrical line is turned ON or OFF. In this project, a separate password is provided to each electrical line. Activation and deactivation of the line (circuit breaker) is indicated by the load (Light Bulbs).
Circuit Diagram of Password based Circuit Breaker
Components Required
8051 Microcontroller (AT89C52) 8051 Development Board 8051 Programming Board (Programmer) 4 x 4 Matrix Keypad 4 – Channel Relay Module 16 x 2 LCD Display 10KΩ Potentiometer 4 Loads (Light Bulbs) Power Supply Connecting Wires If 8051 Development Board is not used, then you need 0592 MHz Crystal 2 x 33pF Capacitor 2 x 10KΩ Resistors (1/4 Watt) Push Button 10µF Capacitor (Electrolytic) 1KΩ x 8 Pull – up Resistor Pack If Relay Module is not used, then you need (components mentioned for one load) 5V or 12V Relay 1KΩ Resistor (1/4 Watt) BC547 NPN Transistor 1N4007 PN Junction Diode
How to Design Password based Circuit Breaker Circuit?
The above circuit consists of 8051 series controller (AT89C52), 4×4 Matrix Keypad, 16 x 2 LCD Display, 4 – Channel Relay Module and Four Loads. LCD data pins are connected to PORT1 and control pins RS, RW and EN pins are connected to P3.0, GND and P3.1 respectively. Here, the LCD is used to display the information related to the load. Keypad is connected to PORT2 of the microcontroller. The four Row Pins of the Keypad are connected to P2.0 to P2.3 and the four Column Pins are connected to P2.4 to P2.7. Using this keypad, we need to enter the password. Four Lamps (acting as Electrical Lines) are connected to P0.0 to P0.3 through the 4 – Channel Relay Module. These are used to indicate circuit breaker state (Light ON – Line Active and Light OFF – Line Not Active). If you are not using the Relay Module, then you need to use 4 BC547 NPN Transistors (along with its current limiting base Resistor) in order to drive the relays. WARNING: Be extremely careful when wiring the AC load to the Relay and mains supply.
Algorithm
Simulation Video
How to Operate the Password based Circuit Breaker Project?
Download Project Code
Advantages
Avoids electrical accidents to line man Project is simple and easy Uses commonly available components
Applications
Used in electrical substations to ensure line man safety This system is used in buildings and houses Used in hotels and shopping malls to save the power. Can also be used as Password based electrical appliance control or Password based Load Control system.
I want to implement that in my home. Thanks. Are you trying to make the same project or different one? Yes, were trying to make the same project. Thanks, ishaanpandey200@gmail.com I really want to do this project. Am A Final year POWER student. Pls all I need from you now is to help me with the codes, for am running out of time now….. I awaits your response Sir. Thanks…. Comment * Name * Email * Website
Δ
